Little GIANT 506065 Bedienerhandbuch PDF herunterladen

ENGLISH

This instruction sheet will provide you with information required to safely own

and operate your Little Giant WRSC-6 kit. This unit is designed to pump

wastewater from laundry trays, washing machines, sinks, or dehumidifiers. It is

not designed to pump raw sewage, fluids other than water, or fluids with solids.

The inlet screen will remove many solids over 1/8” diameter, but large amounts

of solids can clog screen and result in pump failure. Maximum fluid temperature

is 125° F. Unit is designed to fit under most sinks so in many cases it is not

necessary to recess the unit into the floor.

This instruction sheet covers the standard models in this pump series. This form

is applicable to other models in this series not listed by catalog number in the

replacement parts list section of this pamphlet. If the catalog number of your

pump is not listed in the replacement parts section, then exercise caution when

ordering replacement parts. Always give the catalog number of your pump

when ordering replacement parts.

The Little Giant unit you have purchased is of the highest quality workmanship

and material. It has been engineered to give you long and reliable service.

Little Giant pumps are carefully packaged, inspected, and tested to ensure safe

operation and delivery. When you receive your pump, examine it carefully to

determine that there are no broken or damaged parts that may have occurred

during shipment. If damage has occurred, make notation and notify the firm

where you purchased the pump. They will assist you in replacement or repair,

if required.

READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL,

OPERATE OR SERVICE THE LITTLE GIANT PUMP. KNOW THE PUMP

APPLICATION, LIMITATIONS, AND POTENTIAL HAZARDS. PROTECT

YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION.

FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN

PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS

FOR FUTURE REFERENCE.

SAFETY GUIDELINES

1. Make certain that the unit is disconnected from the power source before

attempting to service or remove any component!

2. Do not use to pump flammable or explosive fluids such as gasoline, fuel

oil, kerosene, etc. Do not use in explosive atmospheres or hazardous

locations as classified by NEC, ANSI/NFPA70. Pump should be used with

liquids compatible with pump component materials.

3. Do not handle the pump with wet hands or when standing on a wet or

damp surface or in water.

4. Do not pull the pump out of the water by the power cord when the pump

is operating or connected to power source.

5. This pump is supplied with a grounding conductor and/or grounding-type

attachment plug. To reduce the risk of electrical shock, be certain that it is

connected to a properly grounded grounding type receptacle.

6. The National Electric Code requires a ground fault circuit interrupter (GFCI)

be installed in the branch circuit supplying fountain equipment, pools, etc.

7. In any installations where property damage and/or personal injury might

result from an inoperative or leaking pump due to power outages,

discharge line blockage, or any other reason, a backup system(s) and/or

alarm should be used.

8. Support pump and piping during assembly and when installed. Failure to do

so may cause piping to break, pump to fail, motor bearing failures, etc.

9. The pump motor is equipped with an automatic resetting thermal protector

and may restart unexpectedly. Protector tripping is an indication of motor

overloading as a result of excessively high or low voltage, inadequate

wiring, incorrect motor connections, or a defective motor or pump.

10. If pump is an oil-filled pump, the motor housing is filled with a dielectric

lubricant at the factory for optimum motor heat transfer and lifetime

lubrication of the bearings. Use of any other lubricant could cause damage

and void the warranty. This lubricant is non-toxic; however, if it escapes the

motor housing, it should be removed from the surface quickly by placing

newspapers or other absorbent material on the water surface to soak it up,

so aquatic life is undisturbed.

ELECTRICAL CONNECTIONS

1. Check the pump label for proper voltage required. Do not connect to

voltage other than that shown.

2. If pump is supplied with a 3-prong electrical plug, the third prong is to ground

the pump to prevent possible electrical shock hazard. DO NOT REMOVE the

third prong from the plug. A separate branch circuit is recommended. Do not

use an extension cord. Do not cut plug from the cord. If the plug is cut or the

cord is shortened, then this action will void the warranty.

3. If the cord is equipped with stripped lead wires, such as on 230 V models, be

sure that the lead wires are connected to a power source correctly. The (green/

yellow) wire is the ground. The (blue or white) and the (brown or black) are live.

CONSULT INSTRUCTION SHEET ILLUSTRATIONS FOR PROPER

ASSEMBLY AND DISASSEMBLY OF YOUR LITTLE GIANT PUMP.

4. Check local electrical and building codes before installation. The installation

must be in accordance with their regulations as well as the most recent

National Electrical Code (NEC).

5. Plug into a grounded receptacle with vent tube pointed down. Vent tube

must remain unobstructed for proper pump operation.

6. If installed in basement, plug connection should be four feet or more above floor,

especially if basement floods. Be sure electrical connections cannot be reached by

rising water. Under no circumstances should outlet box or receptacle be located

where it may become flooded or submerged by water.

OPERATION

1. Determine proper location for unit. Unit should be located so that inlet is gravity-fed.

Unit will not draw water up from a lower level. Position and level basin. Keep basin

away from any item that could puncture basin. Position selected should be

convenient to inlet, discharge and vent piping and electrical supply.

2. Plumb inlet. Using proper adapter, plumb discharge to basin cover fitting. Use a

P-trap and a union next to the basin. Use pipe joint compound and hand tighten

only on plastic fittings. A 1-1/2" MNPT x 2" slip pipe adapter is provided if a 2" inlet

is required. See "Typical Installation."

3. Plumb discharge. Using proper adapter, plumb discharge to basin cover fitting. Use

a swing check valve as close as possible to top of basin cover and union. Be sure

check valve is installed in proper flow direction. If check valve is installed backwards,

no water will flow out of unit. Be sure discharge piping is sealed with pipe joint

compound and that lift height of pump is not exceeded. Hand tighten only on plastic

fitting. A 1-1/2" MNPT x 2" slip pipe adapter is provided if a 2" discharge is required.

4. Plumb vent. Plumb vent using 2" threaded pipe to fitting in basin cover. Use pipe

joint compound on threads and hand tighten only on plastic fittings. The basin must

be vented in accordance with state and local codes. A 2" MNPT x 1-1/2" Slip pipe

adapter is provided if a 1-1/2" vent is required.

THIS UNIT WILL NOT OPERATE WITHOUT PROPER VENTING. CAUTION: Do not

use a mechanical vent with this product. A mechanical vent will cause improper

operation of the automatic switch.

5. Test Unit. Connect power cord to electrical supply as stated in ELECTRICAL

CONNECTIONS. Secure power cord to piping

with ties or tape. Fill unit with

water through inlet. Pump should turn on with 4" to 7" (10.2 - 17.8 cm) of

water in tank, and turn off when 1½" to 3½" (3 - 8 cm) of water is left in tank.

See Pump Troubleshooting Guide if problems occur.

WRSC-6

63(&,),&$7,216&$5$&7e5,67,48(67(&+1,48(6(63(&,),&$&,21(6

Model No.

Modèle No.

N° de Modelo

Catalog No.

Rèfèrence

Catalogue

Cataloga

Número

Volts

Voltios

Hertz

Amps

Ampères

Amperios Watts

Watts

Gallons per hour (GPH) at ht.

Litres par huere

Litros por hora

Shutoff (FT.)

Hauteur à

débit nul

A Válvula

Cerrda

PSI

Kg/cm2S R

5' 10' 15'

WRSC-6 506065 115 60 13 9 720 2750 1750 750 18 7.8

WRSC-6 506066 230 50 7 5 720 2580 1050 — 12 5.2

Franklin Electric Co., Inc.

Oklahoma City, OK

)D[

www.LittleGiantPump.com

[email protected]

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - OPERATION

ENGLISHENGLISHENThis instruction sheet will provide you with information required to safely own and operate your Little Giant WRSC-6 kit. This

Seite 2 - FRANÇAIS

FRFRANÇAISFRCette liste de directives vous fournit les renseignements nécessaires pour utiliser une WRSC-6 Little Giant en toute sécurité. Ce

Seite 3 - Figure 2

',5(&7,9(6'(6e&85,7e 1. Votre pompe demandera très peu d’entretien. Si, pour une raison quelconque, elle ne peut pas

Seite 4 - ADVERTENCIA

FONCTIONNEMENT 1. Installer la pompe à un endroit adéquat. Elle devrait être placée de manière à ce que l’entrée soit alimentée par gravité, car elle

Seite 5 - INSTRUCCIONES DE SERVICIO

6. El Código Eléctrico Nacional (National Electric Code) requiere la instalación de un interruptor de circuito por falla a tierra (GFCI) en el ramal

Seite 6

7528%/(6+227,1*,1)250$7,21,1)250$7,21685/$5(/Ë9('(6'e5$1*(0(176 ,1)250$&,21'(,19(67,*$&,21'($9(5,$6352%/(0

Seite 7 - Figure 3

Mounting hole lines up with a locating rib on the inside of the EDVLQ/HWURXGHPRQWDJHV·DOLJQHDYHFXQHQHUYXUHGHSRVLWLRQQHPHQWVLWXpHjO·LQW

Seite 8 - Little Giant

87+(&203$1<6+$//127%(/,$%/()25,1&,'(17$/&216(48(17,$/2563(&,$/'$0$*(668&+AS, BUT NOT LIMITED TO:DAMAGE

Kommentare zu diesen Handbüchern

Keine Kommentare

Little GIANT 506065 Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Wasserpumpen Little GIANT 506065 herunter. Little GIANT 506065 Instructions / Assembly Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Wasserpumpen Little GIANT 506065